The UniFi Access G2 Starter Kit is the second generation of the basic set of components to install the UniFi Access access system. The set is compatible with most electric locks, magnetic locks and a whole range of 12V accessories such as motion sensors, buttons and alarms. The installation of the entire ecosystem is very fast, easy and offers simple management of users, visitors, plans and levels or access permissions via UniFi Access Controller. The set is powered via PoE, which is not included in the delivery.
Note: UniFi Dream Machine Pro is required to operate UniFi Access.

Package contents:
•(1) UniFi Access Door Hub (hub / controller)
•(1) UniFi Access Reader G2 (reader)
•(10) UniFi Access Card

Warranties - Returns:
Money Return:	Repair - Replacement:
20 days	24 months

Specifications
UA-Hub-Door Mechanical
Dimensions	174.9 x 126 x 32.9 mm
Weight	363 g
Enclosure material	Polycarbonate
Mounting material	Polycarbonate
Hardware
Networking Interface	(5) 10/100/1000 Base-T
Power method	PoE++ UL 294 Power-limited Class 2 PSU UL 60950/62368 LPS/PS2 PSU
Max. Power Consumption	Without PoE output: 30W With PoE output: 50W
PoE input	50V DC, 1A
PoE output	PoE passthrough, (4) PoE, 50V DC, total 20W
Button	(1) Factory-reset
LEDs	System: white/blue Output relays: white
Digital input	Request to exit/request to enter/remote release/door position sensor
Dry output relay	Lock: 30V DC, 1A Aux: 30V DC, 1A
Powered output relay	Lock: 12V DC, 1A Aux: 12V DC, 0.33A 12V DC, 0.33A
Operating environment	Indoor use only
Operating temperature	0 to 40° C
Operating humidity	5 to 95% noncondensing
UL 294 level	Destructive attack: Level I Line security: Level I Endurance: Level I Standby power: Level I
UL 294 statement	Compliance with IEEE 802.3 (at or af) specifications was not verified as part of UL 294. The equipment is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits.
CAN/ULC-60839-11-1 Grade	Grade assignment: 1
Certifications	CE, FCC, IC, UL 294, CAN/ULC-60839-11-1
Document number, and issue date and/or revision level	UA-Hub-Door002, V01
LEDs
PoE in	Steady blue: Adopted/device is ready Steady white: Pending adoption Blinking white/blue: Upgrading firmware
PoE out	Off: Not connected or no data link Steady blue: Connected and data link on
UA-G2 Mechanical
Dimensions	93 x 40 x 36.5 mm
Weight	82 g
Enclosure material	Polycarbonate, glass
Mounting	In Wall, gang box
Weatherproofing	IP55
Hardware
Networking interface	(1) 10/100 MbE RJ45 port
Connectivity	BLE 4.1
Power method	PoE
Supported voltage range	48V DC
Max. power consumption	5W
ESD/EMP protection	Air: ±15kV, contact: ±8kV
Sensors	Proximity sensor
Speaker	(1) 8 ohm, 0.7W
LEDs	R/G/B/W
Button	(1) Factory-reset
NFC frequency	13.56 MHz
NFC read range	< 30 mm
NFC standards	ISO 14443A, 14443B, 15693
NFC technology	NFC Tag 1,2,3,4,5 MIFARE Classic MIFAREPlus MIFARE Ultralight MIFARE DESFire
Operating temperature	-30 to 45° C
Operating humidity	5 to 90% noncondensing
Certifications	CE, FCC, IC
UA-Card Mechanical
Dimensions	85.6 x 53.98 x 0.84 mm
Weight	5 g
Format	ISO 7810 ID-1
NFC frequency	13.56 MHz
NFC technology	ISO/IEC 14443 Type A MIFARE DESFire UniFi Access Proprietary Security Protocol

Wiring Information
Typical installation (Shielded)
DC power input	Belden 8750 18 AWG 2 conductor (30.5 m)
Door position switch	Belden 8750 18 AWG 2 conductor (152.5 m)
Request to exit	Belden 8750 18 AWG 2 (152.5 m)

Wiring gauge requirements (AWG)
Total length to device	Output load current at 12V DC
	100mA	250mA	500mA	1A
6.1 m	22	22	22	18
15.2 m	22	22	22	18
30.5 m	22	22	18	18
PoE cabling requirements	The minimal conductor gauge permitted to connect between the PSE or power injector and the PD shall be 24 AWG (0.21 mm²) for horizontal or riser cable.